• One week STTP on topic “Recent Developments in Manufacturing System” was organized by Department of Mechanical Engineering in 2019.

Publications

  • Chauhan, Dr. P.S. (2017). “Finite element analysis of nodular cast-iron camshaft”. International Journal of Engineering Research and Technology, Volume. 6, Issue. 05.

  • Bhaduria, Omvir Singh, Goyal Sanjay & Chauhan, Premanand S. (2016). “Application of taguchi for optimization of process parameters for minimum surface roughness in turning of 45C8”. International Journal of Current Engineering & Scientific Research, 1(1), 47-54.

  • Dwivedi, Dev Dutt & Jain, V.K. (2016). “Review paper on design and fatigue analysis of leaf spring for automobile suspension system”. International Journal of Current Engineering & Scientific Research, 1(1), 96-101.

  • Dwivedi, Dev Dutt & Jain, V.K. (2016). “Design and analysis of automobile leaf spring using ANSYS”. International Journal of Current Engineering & Scientific Research, 1(1), 102-107.

  • Goyal, Priyanka & Husain, Juber (2016). “Modeling simulation and kinematics analysis based on PRO/Engineer for boom of backhoe loader”. International Journal of Current Engineering & Scientific Research, 1(1), 139-141.

  • Gupta, Adviteeya, Chauhan, Premanand S. & Arya, Prabhu Dayal (2016). “Effect of hardness and notch on tensile strength of v-notched SUP 9A BAR’’. International Journal of Current Engineering & Scientific Research, 1(1), 158-166.

  • Dhaker, Pooran S. & Mishra, S. G. (2016). “Components design of hoisting mechanism of 5 ton EOT Crane”. International Journal of Current Engineering & Scientific Research, 1(3), 113-117.

  • Jain, Abhishek., Arya, Prabhu Dayal & Bansal, Ashutosh. (2016). “Management of energy & waste and sustainable environment in shopping malls- An empirica study”. International Journal of Current Engineering & Scientific Research, 1(2), 51-57.

  • Sharma, Avadesh K., Chauhan, Premanand S., Narwariya, Manoj & Pankaj, Rajkumar. (2016). “Vibration analysis of functionally graded plates with multiple circular cutouts”. International Journal of Current Engineering & Scientific Research, 2(3), 15-21.

  • Agrawal, Abhay., Rana, R. S., Shrivastava, P. K. & Singh R. P. (2016). “A short review on solar water distillation for getting fresh water in rural area”. International Journal of Current Engineering & Scientific Research, 2(3), 111-120.

  • Chauhan, Premanand S., Dwivedi, Ravi K. & Sharma Sudhir. (2016). “Optimization of surface roughness of a drilled hole on SUP 11A by taguchi's optimization technique”. International Journal of Current Engineering & Scientific Research, 2(3), 142-148.

  • Tomar, Ravinandan Singh & Narwariya, Manoj. (2016). “Fillet weld analysis utilizing ANSYS : Study of loading condition”. Journal of Advancements in Robotics .ISSN: 2455-1872. Vol-3( 1),49-56.

  • Tomar, Ravinandan Singh & Narwariya, Manoj. (2016). “Fillet weld analysis utilizing ANSYS : Study of loading meshing method. Journal of Mechatronics and automation. ISSN 2455-1988.Vol-3(1), 1-5.

  • Narwariya, Manoj (2016).“Vibration analysis of functionality graded plates with multiple circular cutouts”. International Journal of Current Engineering & Scientific Research.

  • Gupta, Sachin, & Chauhan, Premanand S., (2016). “Stress analysis of bevel gear tooth using FEA: A review”. International Journal for Scientific Research & Development, 4(2), 1325-1328.

  • Gupta, Sachin, Chauhan, Premanand S., & Hussain, J (2016). “Stress analysis of bevel gear tooth using FEA”. International journal of engineering technology science and research, 3(5), 116-121.

  • Kankar, Krishnakant & Singh, R. P. (2015). “Design of spur gear and its tooth profile on MATLAB”. Asia Pacific Journal. Vol.-I, 29-44.

  • Kankar, Krishnakant & Singh, R. P. (2015). “Design of spur gear and its tooth profile for a given power”. International Journal of Science, Engineering and Technology Research. Vol-4.

  • Gupta, Adviteeya & Chauhan, Premanand S. (2015). “Effect of hardness and notch on strength of SUP 9A: a review”. International Journal of Science and Engineering, 3 (2), 116-122.

  • Narwaria, Uttam S., Chauhan, Premanand S. & Husain, Juber (2015). “Finite difference formulation of fin for electronics cooling”. International Journal of Emerging Technology and Advanced Engineering, 5(7), 431-435.

  • Narwaria, Uttam S., Chauhan, Premanand S. & Husain, Juber (2015). “Finite difference simulation of fin for electronics cooling”. European Journal of Advances in Engineering and Technology, 2(9), 34-38.

  • Pandit, Prem Prakash & Chauhan, P. S. (2015). “Unsteady simulation of rectangular fin for cooling of automobile engine”. International Research Journal of Management Science and Technology, 6 (4), 124-133.

  • Pandit, Prem Prakash & Chauhan, P. S. (2015). “Numerical study of rectangular fin for cooling of automobile engine”. ELK Asia Pacific Journal of Mechanical Engineering Rresearch, 1(2), 1-7.

  • Chauhan, P. S. & Agrawal, C. M. (2014). “Identification of manufacturing defects leading to rejection during manufacturing of stabiliser bar”. International Journal of Productivity and Quality Management, 14 (4), 408–422.

  • Chauhan, P. S., Agrawal, C. M. & Dwivedi, R. K. (2014). “Effect of material and process parameter on dimensions of rolled external threads”. Applied Mechanics and Materials Journal, 493, 453-460.

  • Chauhan, P. S. & Agrawal, C. M. (2013). “Optimization of blank parameters of rolled threads by taguchi method”. Proceedings of International Conference on Future Trends in Structural, Civil, Environmental and Mechanical Engineering, Bangkok, 94-99.

  • Jadon, Ganesh. (2012). “Determination of maximum recommended weight limit for manual lifting task in industry through taguchi parametric optimization technique”. International Journal of Mechanical and Industrial Engineering (IJMIE), ISSN No. 2231 – 6477, Vol-1(3).

  • Jadon, Ganesh. (2012). “Analysis of load constant in manual material handling task by taguchi technique & mathematical regression modeling”. International Journal of Modern Engineering Research (IJMER), ISSN: 2249-6645, Vol-2(4). 2512-2515.

  • Jadon, Ganesh. (2012). “Evaluation of load constant of worker in industry by using a fuzzy logic approach”. International Journal of Engineering Research & Technology (IJERT) ISSN: 2278-0181, Vol-1(5).

Approval , Recognition, and Affiliation

hi hi 3 hi 3 3 3